Chiligreen P4VTC Manual do Utilizador

PPP444VVVTTTCCC i FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device,

8Front Panel Connector: JPANEL1 Front USB Header: JUSB3/ JUSB4 Pin Assignment Pin Assignment 1 +5V(fused) 2 +5V(fused) 3 USBP4- 4 USBP5- 5 USBP4

9Power Connectors: JATXPWR1/ JATXPWR2 PIN Assignment PIN Assignment 1 +3.3V 11 +3.3V 2 +3.3V 12 -12V 3 Ground 13 Ground 4 +5V 14 PS_ON 5 Ground 15

10Power Source Selection for USB: JUSBV1/ JUSBV2/ JUSBV3 JUSBV1/JUSBV2/ JUSBV3 Assignment Description 1 3 Pin 1-2 close +5V JUSBV1: 5V for USB l

11※ Clear CMOS Procedures: 1. Remove AC power line. 2. Set the jumper to “Pin 2-3 close”. 3. Wait for five seconds. 4. Se

12Front Panel Audio Header: JAUDIO1 (optional) 12121516 JAUDIO1 Pin Assignment Pin Assignment 1 Mic In 2 Ground 3 Mic Power 4 Audio Power

13Serial ATA Connector: JSATA1/ JSATA2 Pin Assignment Pin Assignment 1 Ground 2 TX+ 3 TX- 4 Ground 5 RX- 6 RX+ 741 JSATA1/ JSATA2 7 Ground Ba

14WarpSpeeder Introduction [ WarpSpeeder™ ], a new powerful control utility, features three user-friendly functions including Overclock Manager,

15Installation 1. Execute the setup execution file, and then the following dialog will pop up. Please click “Next” button and follow the default

16 Usage The following figures are just only for reference, the screen printed in this user manual will change according to your motherboard on ha

17This utility is responsible for conveniently invoking [WarpSpeeder™] Utility. You can use the mouse by clicking the left button in order to invo

CCCooonnnttteeennnttt iiLAYOUT OF P4VTC ...1 COMPONENT INDEX...

18 3. Voltage Panel Click the Voltage button in Main Panel, the button will be highlighted and the Voltage Panel will slid

19 4. Overclock Panel Click the Overclock button in Main Panel, the button will be highlighted and the Overclock Panel

20 Overclock Panel contains these features: a. “–3MHz button”, “-1MHz button”, “+1MHz button”, and “+3MHz button”: provide user the ability

21 c. “Auto-overclock button”: User can click this button and [ WarpSpeeder™ ] will set the best and stable performance an

225. Hardware Monitor Panel Click the Hardware Monitor button in Main Panel, the button will be highlighted and the Hardware Monitor panel will s

23 Note: Because the overclock, overvoltage, and hardware monitor features are controlled by several separate chipset, [

24StudioFun!TM (Optional) Introduction StudioFun!TM is a media-player based on optimized GNU/Linux distribution to bring a “Room Theater” experien

25Trouble Shooting PROBABLE SOLUTION No power to the system at all Power light don’t illuminate, fan inside power supply does not turn on. Indicat

26 08/13/2003

1Layout of P4VTC ※ NOTE: ●represents the first pin. JKBMS1Mouse &KeyboardJUSB1JATXPWR212JKBV11JAUDIO1USB JUSBV1Parallel PortJCOM1COM1C

2Component Index A. Power Source Selection for Keyboard N. Wake On LAN Header (JWOL1) and Mouse (JKBV1) O. System FAN

3English P4VTC Features A. Hardware CPU Provides Socket 478. Supports the Intel® processor. Supports Hyper-Threading Technology. F

4On Board Peripherals a. Rear side 2 serial ports. 1 parallel port. (SPP/EPP/ECP mode) Audio ports in vertical position. 1 LAN jack. PS/2 m

5How to setup Jumper The illustration shows how jumpers are setup. When the Jumper cap is placed on pins, the jumper is “close”. If no jumper cap

6CPU Fan Header: JCFAN1 Pin No. Assignment 1 Ground 2 +12V 13 JCFAN1 3 FAN rpm rate Sense System Fan Header: JSFAN1 Pin No. Assignment 1 Ground

7Jumpers, Headers, Connectors & Slots Floppy Disk Connector: FDD1 The motherboard provides a standard floppy disk connector that supports 360K